Inside the Calibre Course: How We Teach a Miyota 82S0, One Stage at a Time

Petter Trobe

When people first open a mechanical movement, the hard part is rarely a single screw. It is the sequence. A movement only comes apart in one order and only goes back together in the reverse, and a beginner who tries to learn all of it at once usually loses track somewhere in the middle.

The course in the Calibre Learning Kit is built around that problem. Here is how it works, and why we chose to teach it this way.

Sixteen steps, introduced gradually

Taking a Miyota 82S0 apart and rebuilding it is broken down into 16 steps. Instead of showing all 16 in one long film, the course adds them a few at a time:

  • Steps 1 to 2: the rotor and the balance.
  • Steps 1 to 4: adding the pallet fork and the going train.
  • Steps 1 to 8: adding automatic winding, the mainspring barrel and the hacking mechanism.
  • Steps 1 to 12: adding the click spring, the hour wheel bridge and the setting wheels.
  • Steps 1 to 16: the keyless works, the bare main plate and the complete movement.

Notice that every chapter starts again from step 1. That is deliberate. By the time you reach the full movement you have taken the rotor off and put it back five times. The early steps become routine, and your attention is free for the new parts.

Every chapter has three parts

Disassembly. A video takes the movement apart up to that chapter's stage, filmed close up so you can see exactly where the tweezers go and which way a part lifts out.

Assembly. A second video rebuilds it in reverse. This is where most of the learning happens: seating a pivot in its jewel, letting a bridge settle on its own instead of forcing it, checking that a wheel turns freely before moving on.

A short quiz. Three questions on the details that matter most at that stage, such as how to keep the hairspring safe when the balance bridge comes off, or what tells you the train wheels are aligned under their bridge. If you can answer them, you are ready for the next chapter.

Before you touch the movement

The course opens with a welcome, a walkthrough of the Bergeon tools in the kit, and the seven commandments of the bench: the handful of habits that prevent most beginner mistakes. They are simple things, like working on a clean, light surface, never forcing a part, and stopping when you are tired. They are also the things experienced watchmakers never skip.

Why a real movement

We could have built the course around a model. We chose a genuine Miyota 82S0 because a real movement gives honest feedback. If a pivot is not in its jewel, the bridge will not sit flat. If the pallet fork is not free, the balance will not start. Nothing in a model needs to be that precise, so it cannot teach you that kind of attention. You can read more about the movement itself in What Is the Miyota 82S0 Movement?

Where the course lives

The lessons are hosted on Calibre Academy, our own learning platform. Each kit comes with an access code. If you already have a Miyota 82S0 and your own tools, you can also buy the course on its own. Either way, you can follow the course at your own pace and return to any lesson whenever you need a reminder. The full chapter overview is on our course page.

Who teaches it

Calibre Project comes from a family of watchmakers. Petter Trobe started it after growing up in the workshop of his father, Kåre Arthur Trobe, whose own father, Egil Walter Trobe, was a watchmaker before him. The lessons are developed together with Swiss-trained watchmakers, so what you learn at your kitchen table is the same technique used at the bench.

FAQ

How many chapters does the Calibre course have?

Six: an introduction and five stages that build up to the complete Miyota 82S0 movement over 16 steps.

Is there a test along the way?

Yes. Each stage ends with a short quiz on the key details of that stage.

Do I need experience to start?

No. The course is made for complete beginners and starts with the tools and the basic rules of the bench.

Can I buy the course without the kit?

Yes. The course is included with the Calibre Learning Kit, but if you already have a Miyota 82S0 movement and suitable tools you can buy the course on its own in Calibre Academy.

Tilbake til bloggen