How a Swiss Lever Escapement Works: Why Your Watch Ticks

Petter Trobe

Hold a mechanical watch to your ear and you hear it: a small, dry tick, six or eight times a second. That sound is not the gears turning and it is not the mainspring unwinding. It is one specific mechanism doing one specific job, over and over, several hundred million times a year. It is called the escapement, and once you understand it, the rest of the movement starts to make sense.

This is the first article in our How It Works series, where we take one function of a mechanical watch at a time and explain it slowly. We start with the escapement because it is the heart of the matter, and because it is the part you will handle with the most care when you build a movement yourself.

What an escapement is for

A mainspring stores energy. A gear train carries that energy towards the hands. Left alone, the two would simply unwind in a few seconds, like a wind-up toy released on the floor. Something has to stand between the gears and the hands and say: not yet.

The Fondation de la Haute Horlogerie defines the escapement as a mechanism fitted between the gears and the regulating organ, whose function is to suspend the gears' motion at regular intervals and to supply energy to the balance. That sentence contains both halves of the job. The escapement stops the train, and it gives the balance wheel a small push so it keeps swinging.

The balance wheel and its hairspring are the actual timekeeper. They swing back and forth at a fixed rate, the way a pendulum does in a clock. The escapement is the translator between that swing and the gear train: every time the balance passes through the middle of its swing, the escapement lets one tooth of the gear train go, and in return it steals a little energy from the train and hands it to the balance.

The parts you are looking at

The Swiss lever escapement, which is the type in almost every mechanical watch made today, has three parts that matter.

The escape wheel is the last wheel of the gear train. It usually has fifteen teeth with a distinctive hooked shape, and it is the wheel that wants to spin.

The pallet fork, sometimes just called the lever, is a small anchor-shaped part pivoted between the escape wheel and the balance. It carries two synthetic ruby stones, the entry pallet and the exit pallet, that take turns catching the escape wheel's teeth. Its travel is limited by two fixed banking pins.

The balance wheel carries a small disc called the roller, and on the roller sits a single ruby pin: the impulse jewel. The FHH describes the roller as the disc on the balance staff that carries the impulse pin, receives the impulse from the lever and transmits it to the balance. This one tiny pin is the only point where the balance ever touches the rest of the movement.

The cycle: lock, unlock, impulse, drop

Everything happens in four steps, and then it happens again in the other direction.

Lock. At rest, one tooth of the escape wheel is pressed against the locking face of a pallet stone. The whole gear train is stopped. The mainspring is pushing, but nothing moves. Watchmakers call this state rest, or lock.

Unlock. The balance wheel is swinging freely. As it passes through the centre of its arc, the impulse jewel enters the notch at the end of the fork and knocks it sideways. That small knock lifts the pallet stone off the escape-wheel tooth. The train is free.

Impulse. The escape wheel starts to turn, but the tooth cannot simply slide past. It rides across the angled impulse face of the pallet stone, and in doing so it pushes the fork. The fork, in turn, pushes the impulse jewel, and so the balance gets a little shove in the direction it was already travelling. This is the energy that keeps the balance swinging against friction and air resistance.

Drop. The tooth clears the stone and the wheel jumps forward, until the next tooth lands on the locking face of the other pallet stone. That landing is the tick. The fork comes to rest against the opposite banking pin, and a clever bit of geometry called draw keeps it pressed there so it cannot be knocked loose by a bump.

The balance completes its swing, its hairspring pulls it back, and the impulse jewel returns to knock the fork the other way. Tock. Six teeth escape per second in a movement like the Miyota 82S0; the balance receives a push at every one of them.

Why it is called a detached escapement

The genius of the lever is how little contact it needs. For most of every swing the balance is entirely alone, touching nothing but its own pivots. It only meets the fork for a brief moment at the middle of the arc, takes its push, and is free again. This is why the lever is called a detached escapement, and it is the reason it keeps better time than earlier designs, where the balance was in constant contact with the train and every fluctuation in mainspring torque was felt directly.

It also explains why the balance is the part that decides accuracy. If the balance can swing freely, timekeeping depends almost entirely on the balance and hairspring, and on how cleanly the escapement delivers its impulse.

Beat rate: what 21,600 means

Movement specifications quote a frequency in vibrations per hour, or vph. One vibration is one half-swing of the balance, which is to say one tick. A movement running at 21,600 vph makes 21,600 ticks per hour, which is six per second, or 3 Hz. At 28,800 vph the figure is eight per second, or 4 Hz. Older pocket watches ran at 18,000, five per second, and a few high-beat movements run at 36,000, ten per second.

Faster is not automatically better. A higher beat rate makes the balance harder to disturb by a knock or a change of position, which tends to help accuracy, but it also demands more energy from the mainspring, shortens the power reserve and wears the escapement faster. Twenty-eight thousand eight hundred is the modern middle ground; 21,600 is the classic, gentler rate found in movements like the Miyota 82S0 and Seiko's 7S and NH families. When you assemble the 82S0 and see the balance start, you are watching it at 3 Hz.

Where the lever came from

The lever escapement was invented by the English watchmaker Thomas Mudge around 1754 to 1755, and first used in a watch he made for King George III, which the King gave to Queen Charlotte. It was brilliant and, for decades, largely ignored: hard to make, and Mudge himself preferred other work. It took until the nineteenth century, and the industrial methods of Swiss makers like Georges-Auguste Leschot, for the lever to become the standard it is today. The name Swiss lever refers to that later, industrialised form of Mudge's idea.

The co-axial: a modern alternative

The lever's one weakness is that the impulse is delivered by sliding friction: the escape-wheel tooth drags across the pallet stone. That sliding needs oil, and oil degrades. In 1974 the English watchmaker George Daniels invented the co-axial escapement, which separates the locking job from the impulse job and delivers the push radially rather than by sliding, so the pallets can in theory run without lubrication. Omega commercialised it in 1999 in its Calibre 2500 and now uses it across most of its range. In practice a small amount of oil is still applied, but the co-axial remains the only escapement to have seriously challenged the lever in a production wristwatch in two and a half centuries. We tell Daniels' story elsewhere on this blog.

What this means at the bench

When you take a movement apart, the escapement is the reason for the order of operations. The balance comes out first and goes in last, because it is delicate and because nothing else can be tested with it in place. Before you refit it, you check the escapement on its own: nudge the pallet fork with closed tweezers and it should snap cleanly from banking pin to banking pin. That snap is lock and unlock happening under your hand. If it is crisp, the balance will start the moment its impulse jewel finds the fork.

This is the part of the Calibre Learning Kit that people remember. The Miyota 82S0 has an open-heart window over the balance, so the first thing you see when the movement comes back to life is the escapement doing exactly what this article describes, six times a second.

Common misunderstandings

The tick is not the gears. It is the escape-wheel tooth landing on a pallet stone. The escapement is not the timekeeper; the balance and hairspring are, and the escapement is their servant. And vph counts half-swings, not full oscillations, so 21,600 vph is 3 Hz, not 6.

Sources and further reading

Back to blog